R&S ZNL Скачать руководство пользователя страница 1012 | Manualshive

Страница: 1012 / 1135

background image

Command reference

R&S

®

ZNL/ZNLE

1012

User Manual 1178.5966.02 ─ 19

<SensorId>

This optional string parameter is used for power meters that can
control several power sensors, such as the R&S

NRP2. By

specifying the suitable <SensorId> you can address the related
power sensor.
The R&S

NRP2, for example, has four power sensor connec-

tors, Sensor

A to Sensor

D. By specifying

'A'

,

'B'

,

'C'

or

'D'

, you can take control over the power sensor that is attached

to this connector.

Example:

SYST:COMM:RDEV:PMET:CONF:AUTO OFF

Disables "Auto Config NRP-Zxx" (if it was enabled previously).

SYST:COMM:RDEV:PMET1:DEF 'USB Power Meter',
'NRP-Z55', 'usb', '100045'

Configure an R&S NRP power meter as external power meter
no. 1, assigning the name "USB Power Meter" and a serial num-
ber 100045.

SYST:COMM:RDEV:PMET:DEL

Clear the power meter configuration table.

SYST:COMM:RDEV:PMET:DEF?

Query the power meter configuration. The analyzer returns an
error message because the power meter no. 1 is no longer con-
figured.

Manual operation:

See

"Configured Devices"

SYSTem:COMMunicate:RDEVice:PMETer:DELete

Clears the configuration table for external power meters.

Example:

See

SYSTem:COMMunicate:RDEVice:PMETer<Pmtr>:

Usage:

Event

Manual operation:

See

"Configured Devices"

SYSTem:COMMunicate:RDEVice:PMETer<Pmtr>:SPCorrection[:STATe]

<Boolean>

Gets/sets the state of the built-in S-parameter correction that is available on certain
R&S®NRP-Z power sensors.

Note that this state is persistently stored on the power sensor (and NOT on the
R&S

ZNL/ZNLE).

See Application Note 1GP70 "Using S-Parameters with R&S®NRP-Z Power Sensors"
for background information. This Application Note is available on the Rohde & Schwarz
internet at

http://www.rohde-schwarz.com/appnotes/1GP70

Suffix:

<Pmtr>

.

Number of the configured power meter.

VNA command reference

«
...
1010
1011
1012
1013
1014
...
»

Содержание ZNL
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ZNL

Бренд: Valeport Страницы: 25

NUFLO Scanner 2000 microEFM

Бренд: Cameron Страницы: 8

Бренд: Oakton Страницы: 69

Бренд: AccuMac Страницы: 10

Бренд: Chroma Страницы: 63

Ranger TDR VDV501-090

Бренд: Klein Tools Страницы: 44

Бренд: PRONIVO Страницы: 40

Бренд: socomec Страницы: 34

SENSITRON SMART S

Бренд: Halma Страницы: 12

Бренд: Quarton Страницы: 2

Бренд: Horiba Scientific Страницы: 2

Бренд: SensorLink Страницы: 12

IEM-100 Beltpack

Бренд: DAPAudio Страницы: 17

Бренд: PCB Piezotronics Страницы: 11

Бренд: QuantAsylum Страницы: 35

Бренд: 3M Страницы: 168

Бренд: Laserworld Страницы: 5

Бренд: XS Instruments Страницы: 41

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды