Keba ServoOne Скачать руководство пользователя страница 84

Страница: 84 / 493

6.7.2 Absolute value interfaces X8

The following absolute value interfaces will be available at encoder channel Ch3

depending on the X8 option being used.

Cyclical SinCos with SSI one-time reading via X8 option: SINCOS_V2(10) -
2nd SinCos encoder (V2)

Cyclical SinCos with EnDat one-time reading via X8 option: SINCOS_V2(10)
- 2nd SinCos encoder (V2)

Cyclical SSI via X8 options: SINCOS_V2(10) - 2nd SinCos encoder (V2) or
SSI_ECSIM(3) - SSI encoder simulation

Cyclical EnDat via X8 option: SINCOS_V2(10) - 2nd SinCos encoder (V2)

Cyclical HDSL via X8 option: HDSL(15) - HIPERFACE DSL® option
(ServoOne junior only)

They can be selected with P 507[0] - ENC_CH3_Sel and P 570[0] - ENC_CH3_Abs.

For more details, see Section "Main parameters for encoder channel Ch3" on page

82.

6.7.3 BiSS X8

BiSS interfaces are not supported on encoder channel Ch3!

6.7.4 EnDat (cyclical) X8

Ch3: ENDAT(4) - Cyclical EnDat (2.1 or 2.2)

As the EnDat functionality of the parameters for encoder channel Ch3 is

predominantly identical to that of the parameters for encoder channel Ch1, it is

recommended to read the description for the Ch1 encoder channel parameters (see

Section "EnDat (cyclical) X7" on page 62).

ID No.: 0842.26B.5-01 Date: 09.2020

ServoOne - Device Help

6 Encoder

The software versions required to run the EnDat interface are the standard software

versions for the ServoOne and ServoOne junior.

NOTE

Please note the limitations that apply when running EnDat and
SSI encoders (see Section "Limiting for EnDat and SSI" on page
52).

Index Name

Unit Description

507

ENC_CH3_Sel = 4

= ENDAT(4)

573

ENC_CH3_MultiT

Number of MultiTurn bits (absolute encoder)

574

ENC_CH3_SingleT

Number of SingleTurn bits (absolute encoder)

584

ENC_CH3_MTBase

Definition of point of discontinuity in multi-turn
range

585

ENC_CH3_MTEnable

1: Use Multi-turn encoder as a single-turn
encoder

636

ENC_CH3_CycleCount

Position encoder sampling cycle (n x 125 µsec)

600

ENC_CH3_Position

inc

Position encoder channel 3

583

ENC_CH3_
DigitalResolution

Length of one increment (linear absolute encoder)

640

0..29 ENC_ENDAT

EnDat additional (additional information)

Table 6.23: Channel 3 encoder configuration (X8) - EnDat (cyclical) parameters

6.7.5 Hall sensor X8

Encoder channel Ch3 does not support Hall effect sensors!

Содержание ServoOne














































































































































































































































































































































































































































































































Результаты поиска

Содержание ServoOne

Отзывы:

Keba ServoOne, Помощь по устройству, Страница: 84 / 493

Результаты поиска

Содержание ServoOne

Отзывы: