Keba ServoOne Скачать руководство пользователя страница 219

Страница: 219 / 493

Image 7.93: Encoder configuration channel 1 (X7) screen

The settings for the SSI protocol can be made in the following parameters. The

following must be specified here: the SingleTurn and MultiTurn bits, die encoding,

and the minimum MultiTurn position.

Index Name

Value

Unit

Description

543

ENC_CH1_MultiT

Number of multi-turn bits (absolute encoder)

544

ENC_CH1_SingleT

Number of single-turn bits (absolute encoder)

545

ENC_CH1_Code

GRAY

Selection of the encoding of the SSI absolute
encoder

546

ENC_CH1_Mode

0001h

Mode selection: SSI absolute encoder

547

ENC_CH1_MTBase

-
2147483648

Minimum MultiTurn position (SSI absolute
encoder)

548

ENC_CH1_MTEnable

Channel 1: Multi-turn as single-turn

Table 7.100: SSI encoder settings

ID No.: 0842.26B.5-01 Date: 09.2020

ServoOne - Device Help

219

7 Control

Index Name

Value

Unit

Description

598

ENC_CH1_Position

4909

inc

Channel 1: Position

616

ENC_CH1_CycleCount 8

Channel 1: Position encoder sampling cycle
(n x 125

617

ENC_CH1_
AbsInitMode

DIG

Channel 1: Mode of absolute value
initialization

Table 7.100: SSI encoder settings (continue)

The scaling of the units is performed in the motion profile of the standard motor

control. A scaling assistant is available for this purpose (“Scaling / Units” button).

Image 7.94: “Motion profile” screen

Because a volumetric flow rate control underlies the position control, the following

settings must be made beforehand.

The parameter P 2840[8] - QActCalc can be used to select whether the volumetric

flow rate value is to be taken from a sensor (MEAS(0) = From measurement) or, as in

this example, determined by means of a calculation using the cylinder speed and

the pump displacement volume (CYL(1) = From cylinder speed).

Содержание ServoOne














































































































































































































































































































































































































































































































Результаты поиска

Содержание ServoOne

Отзывы:

Keba ServoOne, Помощь по устройству, Страница: 219 / 493

Результаты поиска

Содержание ServoOne

Отзывы: