Keba ServoOne Скачать руководство пользователя страница 211

Страница: 211 / 493

7.11.13 Example: Pressure and pump speed control

This example shows which parameter settings need to be configured in order to

operate a servo pump with pressure and pump speed control. Before configuring the

parameters for the hydraulic system, the settings for the motor and encoder need to

be configured first. After this, “Torque control/Hydraulic control” must be selected as

the control mode and the selection of the reference setpoint must be set to

“Hydraulic profile” in the hydraulic basic settings.

Image 7.82: “Hydraulic basic settings” screen

Index Name

Value

Unit Description

Type

PDO

300

CON_CfgCon

TCON (1)

Select control mode

uint16

159

MPRO_CTRL_SEL

DS402 (5)

Motion profile: selection

uint16

165

MPRO_REF_SEL

HYDRAULIC
(12)

Motion profile: selection

uint16

Table 7.88: Settings for control mode and motion profile

ID No.: 0842.26B.5-01 Date: 09.2020

ServoOne - Device Help

211

7 Control

Now the pump specifications – as found on the rating plate or data sheet – need to

be entered into P 2851 - HYD_Pump. This is also where the minimum and maximum

speed limits for the pump and the gear ratio between the motor and the pump are

set.

Image 7.83: “Pump settings” screen

Index Name

Value

Unit

Description

Type

PDO

2851

HYD_Pump

Pump parameters

2851

displ

5.4

ccm/rev

Offset

float32

2851

cTorque

0.0859437 Nm/bar

Torque constant

float32

2851

pNom

250

bar

Nominal pressure

float32

2851

nNom

1500

rpm

Rated speed

float32

Table 7.89: Pump data settings

Содержание ServoOne














































































































































































































































































































































































































































































































Результаты поиска

Содержание ServoOne

Отзывы:

Keba ServoOne, Помощь по устройству, Страница: 211 / 493

Результаты поиска

Содержание ServoOne

Отзывы: