Keba ServoOne Скачать руководство пользователя страница 42

Страница: 42 / 493

P No.

Index P Name / Setting

Unit Function

Ttherm

Set thermal time constant in seconds

735

MON_MotorI2tType

Motor protection module. Selection of I2T
monitoring method

Off(-1)

Protection disabled

FREQU(0)

Motor frequency-dependent evaluation i(f),
default setting

THERM(1)

Evaluation with thermal time constant i

Tth

. The

thermal time constant is set via parameter

P 733[7]

in [s]. The shut-off threshold based on

measurement tolerances is 110% of the
nominal value.

Table 5.7: “Temperature monitoring” parameters (continue)

NOTE

With a ServoOne junior the temperature sensor cable can be
connected to both X6 and X7.

Does not apply to the ServoOne junior

With ServoOne junior

The following table provides an overview of the selection options for sensor types

with P 732[0] as well as the connection options for the plug-in connectors X5, X6, X7

and X8 (Tech. option) for ServoOne and ServoOne junior.

ID No.: 0842.26B.5-01 Date: 09.2020

ServoOne - Device Help

5 Motor

ServoOne

ServoOne junior / Ser-

voOne Safety

Sensor
type

Parameters

Plug-in connector

(1)

(4)

KTY

P 732[0] = 1, 9

—

PTC

P 732[0] = 2, 4, 12

TSS

P 732[0] = 3

NTC

P 732[0] = 6, 7, 8, 10, 11

—

P 732[0] = 5

, 13

—

1) X6/X7 bridged internally

2) not ServoOne junior

3) only ServoOne junior

4) Tech-opt card X8-HDSL: all settings P732[0].Type = 1..13 are possible! (with HDSL firmware (v3.44.20-xx))

Table 5.8: Temperature sensor connections with plug-in connectors.

Содержание ServoOne














































































































































































































































































































































































































































































































Результаты поиска

Содержание ServoOne

Отзывы:

Keba ServoOne, Помощь по устройству, Страница: 42 / 493

Результаты поиска

Содержание ServoOne

Отзывы: