Keba ServoOne Скачать руководство пользователя страница 451

Страница: 451 / 493

11.6.49 Error 54: Power grid failure error

11.6.49.1 Error 54-1 (emergency code 6100h)

Cause: At least one grid phase missing

Suggested steps:

Check grid wiring

An under-voltage occurred
on the drive while this axis
was switched on.

Power supply was possibly switched off.

Please check if the actual grid voltage matches
the supply setting (parameter PST_
VoltageSupply)

Verify that the grid is stable under load
condition.

ID No.: 0842.26B.5-01 Date: 09.2020

ServoOne - Device Help

451

11 Alarms & warnings

11.6.50 Error 55: Speed guarding error

11.6.50.1 Error 55-1 (emergency code 6100h)

Cause: Speed guarding digital input

Suggested steps:

Check digital inputs

This issue is probably
caused by an unsuitable
parameter setting.

Save your parameter set for a later restore.

See 'history of parameter changes' and undo
the latest changes.

Please check your parameter set for
implausible settings.

Please set device to factory setting, restart, and
see if the error occurs again.

When reporting this error to your service
partner, please include your device's
parameter setting.

The speed control might run
away, most likely due to a
wrong encoder offset.

Please check that the encoder offset is set
properly.

If auto commutation is used, re-view the auto
commutation setting and test under all
possible conditions.

If torque mode is used, reduce torque, ensure
external speed limitation, or increase speed
control gain for stronger limitation.

Содержание ServoOne














































































































































































































































































































































































































































































































Результаты поиска

Содержание ServoOne

Отзывы:

Keba ServoOne, Помощь по устройству, Страница: 451 / 493

Результаты поиска

Содержание ServoOne

Отзывы: