Keba ServoOne Скачать руководство пользователя страница 175

Страница: 175 / 493

Index Name

Unit

Description

2677

CON_PRC_ACTVAL_
FIELDBUS

Current fieldbus value

2678

CON_PRC_OUTSEL_
MOPRO

Process controller: output value for motion
profile

2679

CON_PRC_RefReached USER “Reference value reached” window

2680

CON_PRC_RateLimiter

Process controller: rate limiting

2680

CON_PRC_RateLimiter

x/ms

Slope limitation (Process)

2680

CON_PRC_RateLimiter

x/ms

Process controller: rate limiting, reset I-
component

2681

CON_PRC_CtrlWord

Process controller: control word

2682

CON_PRC_StatWord

Process controller: status word

2683

CON_PRC_REFSEL

Process controller: selection of the reference
value

2684

CON_PRC_REFVAL_
User

Process controller: reference value from user

Table 7.48: “Process controller” parameters (continue)

7.10.5 Scope signals

Index Parameter name

Unit Function

2675

CON_PRC_Cdiff_

Technological controller: control deviation
Process control: control deviation

2666

CON_PRC_RefVal

Technological controller: setpoint
Process control reference value

2673

CON_PRC_Raw_ActVal

Istwert des Eingangssignals
Actual value of input signal

2674

CON_PRC_ACTVAL

Eingangssignal nach Skalierung und Filterung
Input signal after scaling and filtering

2676

CCON_PRC_Outval

Technological controller: output value
Process control output value

Table 7.49: Parameters relevant for visualizing the process control circuit in the
scope

ID No.: 0842.26B.5-01 Date: 09.2020

ServoOne - Device Help

175

7 Control

7.11 Hydraulic control

Firmware with a version range of V270.xx-xx includes special hydraulic parameters

in addition to the standard firmware. These can be used to control pressure,

volumetric flow rate, cylinder speed, and cylinder position, making it easy to

implement hydraulic system applications. The firmware is available for ServoOne,

ServoOne junior and ServoOne safety.

The descriptions in this chapter apply to version V274.30-xx and higher.

7.11.1 Basic setting

In order to activate the hydraulic functionality, the following two basic settings need

to be configured:

1. Chose the control mode via

P 300[0] - CON_CgfCon

: "TCON(1) = Torque

control / Hydraulic control" or "VFCON(0) = V/Hz mode”

Image 7.49: “Hydraulic basic settings” screen

Содержание ServoOne














































































































































































































































































































































































































































































































Результаты поиска

Содержание ServoOne

Отзывы:

Keba ServoOne, Помощь по устройству, Страница: 175 / 493

Результаты поиска

Содержание ServoOne

Отзывы: