Keba ServoOne Скачать руководство пользователя страница 6

Страница: 6 / 493

7.8.2 LHMES(2) method

161

7.8.3 IECON(4) method

162

7.8.4 Test signal generator

163

7.9 V/Hz mode

167

7.10 Process controller

168

7.10.1 Features

168

7.10.2 Description of control structure

7.11 Hydraulic control

7.11.3 Signal setting

181

7.11.4 Hydraulic Limitations

186

7.11.5 Cylinder configuration

190

7.11.6 Hydraulic Motion profile

192

7.11.7 Pressure control

198

7.11.8 Volumetric flow rate control

200

7.11.9 Speed control

203

7.11.10 Position control

205

7.11.11 Digital filter Hydraulics

209

7.11.12 Example: Configuring an MIO module with 0–20 mA sensors

210

7.11.13 Example: Pressure and pump speed control

211

7.11.14 Example: Hydraulic position control

8.2.1 Standard/CiA 402

8.3.1 PG mode with speed control

244

8.3.2 PG mode with position control

245

8.3.3 IP mode with speed control

246

ID No.: 0842.26B.5-01 Date: 09.2020

ServoOne - Device Help

Table of contents

8.3.4 IP mode with position control

247

8.3.5 Jerk limitation and speed offset

8.5.2 Method (-13): Absolute encoder

254

8.5.3 Method (-12): Set absolute position (absolute measuring system)

255

8.5.4 Method (-10) and Method (-11): Move to block with zero pulse

255

8.5.5 Method (-8) and (-9): Move to block

256

8.5.6 Method (-7) to (0)

257

8.5.7 Method (1) and Method (2): limit switch and zero pulse

258

8.5.8 Method (3) and (4): Positive reference mark and zero pulse

259

8.5.9 Homing methods 5 and 6: Negative reference mark and zero pulse

260

8.5.10 Method (7) to (10):

261

8.5.11 Method (11) to (14): Reference mark, zero pulse and negative limit switch

262

8.5.12 Methods (15) and (16)

264

8.5.13 Method (17) to (30): Reference mark

264

8.5.14 Methods (31) and (32)

265

8.5.15 Method (33) and (34): with zero pulse

8.6.3 Manual mode window, "Jog mode" tab

268

8.7 Reference table

268

8.8 Analogue channel (ISA00 und ISA01)

273

8.8.1 Special characteristics of position control mode

274

8.8.2 Wire Break Monitoring

8.11 Synchronized motion

279

8.11.1 Electronic cam plate

280

8.11.2 Control word for synchronized motion

282

8.11.3 Status word for synchronized motion

282

8.11.4 Master configuration

283

8.11.5 Electronic gearing

286

Содержание ServoOne














































































































































































































































































































































































































































































































Результаты поиска

Содержание ServoOne

Отзывы:

Keba ServoOne, Помощь по устройству, Страница: 6 / 493

Результаты поиска

Содержание ServoOne

Отзывы: