Keba ServoOne Скачать руководство пользователя страница 220

Страница: 220 / 493

Image 7.95: Volumetric flow rate control screen

NOTE

The cylinder geometry must be configured for the CYL(1) mode
(

The position controller is a PI controller. The control dynamics can be set using P

2848 - HYD_PosCon.

ID No.: 0842.26B.5-01 Date: 09.2020

ServoOne - Device Help

220

7 Control

Image 7.96: “Position control” screen

Index Name

Unit Description

2848

HYD_PosCon

Position Controller Parameters

2848

1/s

Gain of position controller

2848

Position control integration time constant

2848

SFF

Speed feedforward scaling

2848

PosDiffMax

Position tracking error monitoring

Table 7.101: “Hydraulic - position control” parameters

The reference values are generated using the hydraulic motion profile. This

configuration is set up using the motion block table. In this example, table index 0 is

used for position control and table index 1 for speed control. The index is switched

by means of the motion block table using a timer. To do so, the table operating mode

P 2862 - HydOpMode must be set to "Tab(4) = via motion block table". “Tab(2) =

valve control via motion block table” was selected for the valve control P 2840[11] -

CylValueSwSel, meaning that the valve positions must be specified for the

respective table index in the motion block table (P 2863 - Hyd_TabCtrl).

Содержание ServoOne














































































































































































































































































































































































































































































































Результаты поиска

Содержание ServoOne

Отзывы:

Keba ServoOne, Помощь по устройству, Страница: 220 / 493

Результаты поиска

Содержание ServoOne

Отзывы: