manualshive.com logo in svg

Keba ServoOne, Помощь по устройству, Страница: 113 / 493

Поделиться
Скачать
Keba ServoOne Скачать руководство пользователя страница 113

Image 7.3: “Motor control basic settings” screen

7.2.1.1  Adjustment of the mass inertia

If the mass inertia value is not known, the wizard can be used to determine it (see 

Section "Automatic inertia detection" on page 114).

NOTE

 

l

While the mass inertia is being determined the motor executes 

movements. There is a risk that the system and the motor may be 

destroyed.

ID No.: 0842.26B.5-01   Date: 09.2020

ServoOne  - Device Help

113

7  Control

CAUTION!

Your system/motor may be damaged if put into operation in 
an uncontrolled or inappropriate manner.

Improper conduct can cause damage to your system / 

machine.

 

l

Before the “Start” step, make absolutely sure that a valid 
setpoint has been entered, as the configured setpoint 
will be immediately transmitted to the motor after the 
motor control function starts, which may result in the 
motor accelerating unexpectedly.

7.2.1.2  Adaptation to the rigidity of the drive train

The settings for the speed and position control with feed forward control are 

determined automatically by setting the rigidity. The rigidity is stated in percent in the 

wizard.

 

l

The setting < 100% reduces the dynamic performance of the controller 
setting (e.g. for a toothed belt drive).

 

l

The setting > 100% increases the dynamic performance of the controller 
setting (low play and elasticity).

The speed controller gain is scaled separately using the percentage value KP Scale. 

The damping of the control is affected by the speed filter.

Useful settings are:

 

l

Resolver: 1-2 ms

 

l

SinCos encoder (low-track): 0.5 - 1 ms

 

l

SinCos encoder (high resolution): 0.2 - 0.6 ms

Содержание ServoOne














































































































































































































































































































































































































































































































Отзывы:

Нет отзывов