manualshive.com logo in svg

Keba ServoOne, Помощь по устройству, Страница: 306 / 493

Поделиться
Скачать
Keba ServoOne Скачать руководство пользователя страница 306

ID

Index Name / Setting

Unit Description

function can also be activated by parameter 

P 269[0] - MPRO_TAB_Ctrl

 bit 0.

 

 

TAB0 (23)

 

Binary table index 2^0

 

 

TAB1 (24)

 

Binary table index 2^1

 

 

TAB2 (25)

 

Binary table index 2^2

 

 

TAB3 (26)

 

Binary table index 2^3

 

 

EGEAR (27)

 

Start/Stop electronic gearing

 

 

REFANAEN (28)

 

Enable analogue reference

 

 

ENC (29)

 

Use of ISD05 / ISD06 as encoder input (pulse 
count, pulse/direction).

 

 

HF_SPEC_0 (30)

 

HF specific

 

 

HF_SPEC_1 (31)

 

HF specific

 

 

HF_SPEC_2 (32)

 

HF specific

 

 

HF_SPEC_3 (33)

 

HF specific

 

 

JOG_EXT_POS (34)

 

Jog Positive (extended mode)

 

 

JOG_EXT_NEG (35)

 

Jog Negative (extended mode)

 

 

FAST_DISC (36)

 

Fast discharge of DC link (using a braking 
resistor)

 

 

LIM_OFF (37)

 

Limits off (torque and speed): Torque scaling 
(

P 332[0] - CON_SCON_TmaxScale

) and 

speed limiting (

P 337[0] - CON_SCON_

SmaxScale

) will be disabled (ISDxx = "high"). If 

the function is not parameterized to an input 
(ISDxx = "low") the limits are always active.

 

 

LOCK_POS (38)

 

Lock positive direction: Reversing lock, positive 
direction (access also via iPLC).

 

 

LOCK_NEG (39)

 

Lock negative direction: Reversing lock, 
negative direction (access also via iPLC).

 

 

BRAKE_ON (40)

 

Switch off motor break at once

 

 

PWR_REL_DIRECT (41)

 

Used to manually switch the precharge relay 
(with 1000 ms delay) Use only after consultation 
with KEBA.

 

 

SPINDLECLAMP_S1 (42)  

Switch 1 input

 

 

SPINDLECLAMP_S2 (43)  

Switch 2 input

 

 

SPINDLECLAMP_S3 (44)  

Switch 3 input

 

 

SPINDLECLAMP_P (45)

 

Clamping Pressurized input

Table 9.2:   Function selectors “Digital inputs” (continue)

ID No.: 0842.26B.5-01   Date: 09.2020

ServoOne  - Device Help

306

9  Inputs/Outputs settings

ID

Index Name / Setting

Unit Description

 

 

SlaveBC (46)

 

Brake chopper synchronization only on ISD05 
and ISD06

 

 

USER2 (47)

 

Test case 47

 

 

START_PRC (48)

 

Start process controller

Table 9.2:   Function selectors “Digital inputs” (continue)

9.2.3  Hardware enable – power stage

ServoOne Single-Axis System, ServoOne Multi-Axis System and ServoOne junior 

support the "STO" (Safe Torque Off) safety function in accordance with the 

requirements of EN ISO 13849-1 and EN 61800-5-2 / IEC/EN 62061 / IEC 61508.

NOTE

 

l

For basic information, as well as mandatory planning, wiring, 
commissioning and testing requirements for the STO function, see 
the “STO safety function description” for the ServoOne Single-Axis 
System, ServoOne Multi-Axis System and ServoOne junior (ID 
No.: 1100.10B.x).

The digital input "ENPO" is reserved for the hardware enable. At the setting P 100[0] 

- MPRO_INPUT_FS_ENPO = "OFF(0)" the digital input signal is used merely for safe 

shutdown of the drive and as protection against switching on.

With the setting P 100[0] - MPRO_INPUT_FS_ENPO = “START (1)" in combination 

with P 144[0] - MPRO_DRVCOM_AUTO_START = "ON" autostart mode is activated 

(only in ServoOne). With "STO active" activating the "ENPO" is sufficient to start 

control of the drive. When the "ENPO" is cancelled the drive runs down uncontrolled. 

If the switch-on delay is active, the power stage starts when the preset timer has 

elapsed.

Содержание ServoOne














































































































































































































































































































































































































































































































Отзывы:

Нет отзывов