manualshive.com logo in svg

Keba ServoOne, Помощь по устройству, Страница: 293 / 493

Поделиться
Скачать
Keba ServoOne Скачать руководство пользователя страница 293

ID

Index Name

Unit Description/setting

1423

0

MPRO_CAM_CamMaskConf

 

 

Cam bitmask

This parameter activates / deactivates the cam group 

module.

0: Cam switching value deactivated

1: Cam switching value activated

1423

1

cam mask 1

 

Cam mask 1

1423

2

cam mask 2

 

Cam mask 2

1423

3

cam mask 3

 

Cam mask 3

1423

4

cam mask 4

 

Cam mask 4

Table 8.47:   P 1423 MPRO_CAM_CamMaskConf

8.14.1.5  Direction of movement of the cams of a track

It is possible to configure the parameters on each cam track so that the cams of the 

track are only switched in a specific direction of movement. This is set using P 1424 

MPRO_CAM_CamDirFS.

ID

Index Name

Unit Description/setting

1424

 

MPRO_CAM_CamDirFS

 

 

Directional function selector for each cam track

0: OFF Cams are switched off

1: POSMOVE Cam switching only when moving in 

positive direction

2: NEGMOVE Cam switching only when moving in 

negative direction

3: BOTH Cams are always active (movement in both 

directions) (default)

1424

0

dir fs 1

 

Directional function selector for cam track 1

1424

1

dir fs 2

 

Directional function selector for cam track 2

1424

2

dir fs 3

 

Directional function selector for cam track 3

1424

3

dir fs 4

 

Directional function selector for cam track 4

Table 8.48:   P 1424 MPRO_CAM_CamDirFS

ID No.: 0842.26B.5-01   Date: 09.2020

ServoOne  - Device Help

293

8  Motion profile

8.14.1.6  Assigning cam switching values to an output

The cam group has two outputs (CAMLineA and CAMLineB) which can be used as 

value specifications for the digital outputs.

The parameters for each of the 4 cam tracks can be configured to specify on which 

output (CAMLineA, CAMLineB) the cam switching values should be output. It is also 

possible to output one cam track to both outputs simultaneously.

CAMLineA

CAMLineB

MUX

Cam track 1

Cam track 2

Cam track 3

Cam track 4

MPRO_CAM_CamMuxFS

Image 8.76: Assignment of cam group to output

The assignment of the individual cam tracks to the two outputs can be configured 

with P 1425 MPRO_CAM_CanMuxFS. This makes it possible to configure a total of 

up to 128 cams on one digital output.

Содержание ServoOne














































































































































































































































































































































































































































































































Отзывы:

Нет отзывов