Keba ServoOne Скачать руководство пользователя страница 440

Страница: 440 / 493

11.6.43.5 Error 46-4 (emergency code 8612h)

Cause: Position reference value out of range

Suggested steps:

Quit error and change reference value

Position was limited
internally.

Please check factor group setting and position
command

Take a scope record to determine if the
position control overshoots.

The speed control might run
away, most likely due to a
wrong encoder offset.

Please check that the encoder offset is set
properly.

If auto commutation is used, re-view the auto
commutation setting and test under all
possible conditions.

If torque mode is used, reduce torque, ensure
external speed limitation, or increase speed
control gain for stronger limitation.

ID No.: 0842.26B.5-01 Date: 09.2020

ServoOne - Device Help

440

11 Alarms & warnings

11.6.44 Error 47: Functional safety, common error

11.6.44.1 Error 47-0 (emergency code 6100h)

Cause: Unknown error in functional safety interface detected

Suggested steps:

Acknowledge error, if the error occurs again, reset device

This is probably a software
issue.

Please try to switch to a different version of
device firmware.

Save your dataset and reset the axis module to
factory setting. See if the error persists, or if it
comes with activating a certain feature.

This is possibly a hardware
issue

If other measures fail to solve the problem, please
replace the servo controller.

11.6.44.2 Error 47-1 (emergency code 6100h)

Cause: Communication error to safety system detected

Suggested steps:

Acknowledge error, if the error occurs again, reset device

An error occurred in the
communication to the safety
system.

Please acknowledge the error.

If the error occurs again please restart the
application (24V reset).

This is probably a software
issue.

Please try to switch to a different version of
device firmware.

Save your dataset and reset the axis module to
factory setting. See if the error persists, or if it
comes with activating a certain feature.

Содержание ServoOne














































































































































































































































































































































































































































































































Результаты поиска

Содержание ServoOne

Отзывы:

Keba ServoOne, Помощь по устройству, Страница: 440 / 493

Результаты поиска

Содержание ServoOne

Отзывы: