Keba ServoOne Скачать руководство пользователя страница 196

Страница: 196 / 493

Setpoint for pressure, volumetric flow rate, cylinder speed, cylinder position. The unit

(HYD_UNIT) depends on the control mode and corresponds to bar for pressure

control, l/min for volumetric flow rate control and rpm for pump speed control. For

cylinder position and speed control, the unit corresponds to the UserUnit selected in

the scaling (chapter 8.2). This also applies for derivative 1 and 2 or speed and

acceleration.

Index Name

Unit

Description

2857

HYD_Ref

Hydraulic: Setpoint for volumetric flow
rate/pressure/speed/position

2857

0..15

HYD_Ref

HYD_Unit

Hydraulic: Setpoint for volumetric flow
rate/pressure/speed/position

Table 7.68: “Hydraulic - Reference value” parameters

1st reference value derivative

Rise time/speed of the setpoint

Index Name

Unit

Description

2858

HYD_dRef

Hydraulic: 1st setpoint derivative

2858

0. .15 HYD_dRef

HYD_UNIT/s Hydraulic: 1st setpoint derivative

Table 7.69: “Hydraulic - 1st setpoint derivative” parameters

2nd setpoint derivative

Setpoint acceleration (this parameter is not active for pressure and volumetric flow

rate)

Index Name

Unit

Description

2859

HYD_d2Ref

Hydraulic: 2nd setpoint derivative

2859

0 . .15 HYD_d2Ref

HYD_UNIT/s/s Hydraulic: 2nd setpoint derivative

Table 7.70: “Hydraulic - 2nd setpoint derivative” parameters

ID No.: 0842.26B.5-01 Date: 09.2020

ServoOne - Device Help

196

7 Control

Hydraulic control parameters table

For the control of the valve position, switching of the position controller settings and

of the pump data set as well as for enabling the active decompression, the

respective bits can be enabled in this parameter for every motion block. The active

decompression prevents that a motion block is started as long as pressure is still

applied. If the bit is active, the pressure is reduced via a defined ramp (P 2850.11

decmpRate) below a specified pressure level (P 2850.10 decmpLvl) before the

respective motion block is started.

Bit

Designation

Meaning

ZylArea(A1/A2)

Switchover of the cylinder Area

Reserved

POS

Extend the hydraulic valve cylinder

neg

Retract the hydraulic valve cylinder

Opt1

Valve option 1

Opt2

Valve option 2

PosCon2

Selection for second position-controller setting

P 2871 HYD_PosConAdv2

Reserved

PumpSet2

Selection for second pump data set

P 2873 HYD_Pump2

Reserved

AktivDecomp

Active decompression for the respective motion block

Reserved

PressCon2

Selection for second pressure-controller setting

P 2874 HYD_PressCon2

Table 7.71: Control parameters table

Index Name

Unit Description

2863

HYD_TabCtrl

2863

0. . 15 HYD_TabCtrl

Hydraulic Table control word

Table 7.72: Parameter “Hydraulic table control word”

Scaling of the hydraulic limits

Содержание ServoOne














































































































































































































































































































































































































































































































Результаты поиска

Содержание ServoOne

Отзывы:

Keba ServoOne, Помощь по устройству, Страница: 196 / 493

Результаты поиска

Содержание ServoOne

Отзывы: