manualshive.com logo in svg

Keba ServoOne, Помощь по устройству, Страница: 292 / 493

Поделиться
Скачать
Keba ServoOne Скачать руководство пользователя страница 292

It must always be an even number (i.e. each cam must be defined completely). A 

maximum of 64 cam limit positions are possible.

ID

Index Name

Unit Description/setting

1421

0

MPRO_CAM_CamSizeConf

 

 

Number of defined cam limits for each cam track (max. 

64).

1421

1

size track 1

 

Number of defined cam values on track 1 (always even)

1421

2

size track 2

 

Number of defined cam values on track 2 (always even)

1421

3

size track 3

 

Number of defined cam values on track 3 (always even)

1421

4

size track 4

 

Number of defined cam values on track 4 (always even)

Table 8.45:   P 1421 MPRO_CAM_CamSizeConf

8.14.1.3  Hysteresis value for all cams of a track

To avoid jitter effects, a hysteresis value can be specified for all cams of a track. This 

is configured using P 1422 MPRO_CAM_CamHystConf. The hysteresis value can 

be set individually for each track.

The hysteresis is specified in user units. The value 0 means that no hysteresis is 

effective on this track.

 

2*Hysterese

Hysterese

A

B

C

D

E

Image 8.75: Cam group hysteresis

ID No.: 0842.26B.5-01   Date: 09.2020

ServoOne  - Device Help

292

8  Motion profile

If a value of >0 is entered for the hysteresis, hysteresis is automatically activated for 

all cams on this track. The first time the cam passes through the cam limit, it is 

switched at the original position C. As long as the position then remains in the range 

A-E, any further switching off and switching on takes place at the defined hysteresis 

positions B and D, i.e. switching off at position B, switching on at position D. Only 

when the current position exceeds limit E or is moved to before A again, will the 

output once again be switched at the original position C.

The specification of the hysteresis has an effect on the minimum cam length and the 

minimum cam spacing. The minimum cam length and minimum cam spacing are 

given by the formula:

 

ID

Index Name

Unit Description/setting

1422

0

MPRO_CAM_CamHystConf

 

 

Hysteresis value which can be set per cam track.

1422

1

hysteresis track 1

 

Hysteresis setting for track 1

1422

2

hysteresis track 2

 

Hysteresis setting for track 2

1422

3

hysteresis track 3

 

Hysteresis setting for track 3

1422

4

hysteresis track 4

 

Hysteresis setting for track 4

Table 8.46:   P 1422 MPRO_CAM_CamHystConf

8.14.1.4  Masking of individual cams

Individual cams can be masked out on each cam track. These are then hidden and 

have no effect on the switching of the outputs.

This is set using P 1423 MPRO_CAM_CamMaskConf. The parameter values are 

binary coded. Each bit stands for one cam. A 1 means that this cam is active. A 0 

means that this cam is hidden. By default, all cams are active.

Содержание ServoOne














































































































































































































































































































































































































































































































Отзывы:

Нет отзывов