Keba ServoOne Скачать руководство пользователя страница 307

Страница: 307 / 493

Index Name / Setting

Unit Description

100

MPRO_INPUT_FS_ENPO

Function of digital input ENPO

Off (0)

Hardware enable power stage

START (1)

Hardware enable power stage & start motor control

Table 9.3: “Enable power stage (hardware)” parameters

9.2.4 Digital virtual inputs

Virtual inputs are digital software inputs actuated via iPLC or field bus. The virtual

inputs P 111[0] - MPRO_INPUT_FS_ISV00 and P 112[0] - MPRO_INPUT_FS_ISV0

can use all digital functions which are also available to the real digital inputs.

Index Name

Unit Description

111

MPRO_INPUT_FS_ISV00

Function selector ISV00

112

MPRO_INPUT_FS_ISV01

Function selector ISV01

120

MPRO_INPUT_INV

Digital input inversion: ENPO[0], ISD00..05[1..6], SH[7],
ISD06[16]

Table 9.4: “Digital virtual inputs” parameters

9.2.5 Status of the digital inputs

Clicking on the “Status of digital inputs” field on the input screen for the digital inputs

will open a visualization showing the digital inputs’ states.

ID No.: 0842.26B.5-01 Date: 09.2020

ServoOne - Device Help

307

9 Inputs/Outputs settings

Image 9.3: “Status of digital inputs” screen

Index Name

Unit Description

121

MPRO_INPUT_STATE

Status of digital inputs

Table 9.5: “Status of digital inputs” parameters

9.2.6 Control selector switching

The function selector (MPRO_INPUT_FS_ISDxx) assigns the digital inputs their

functionality.

Using the setting “MAN(14)=Switch control location selector" here will make it

possible to switch the control location via a terminal to the setpoint source selected

in P 164[0] - MPRO_REF_SEL_MAN. This enables fast switching to manual control

for setup or emergency running mode, for example.

Содержание ServoOne














































































































































































































































































































































































































































































































Результаты поиска

Содержание ServoOne

Отзывы:

Keba ServoOne, Помощь по устройству, Страница: 307 / 493

Результаты поиска

Содержание ServoOne

Отзывы: