Invacare Formula CG Seating Скачать руководство пользователя

Страница: 86 / 124

7 SETUP/MAINTENANCE

Invacare® Formula™ CG Seating

Part No 1143155

7.10 Disconnecting/Connecting the Joysticks

SPJ+ Joysticks

Disconnecting

Hold the light GREY collar portion of the joystick connector with one hand and the controller connector on the wheelchair in the other and

disconnect them by pulling them apart.

Connecting

Hold the light GREY collar portion of the joystick connector with

one hand and the controller connector on the wheelchair in the

other and align them.

Lightly push to engage the joystick connector and the controller

connector.

FIGURE

Disconnecting/Connecting the Joysticks - SPJ+ Joysticks



For this procedure, refer to FIGURE

The joystick connector is located at the rear of the seat frame.



WARNING

The joystick connector and controller connector

fit together in one way only. DO NOT force them

together.

Joystick Connector

Light Grey

Collar

Controller

Connector

Содержание Formula CG Seating





























































































































Результаты поиска

Содержание Formula CG Seating

Отзывы:

Похожие инструкции для Formula CG Seating

Бренды по названию

Популярные бренды

Invacare Formula CG Seating, Руководство пользователя

Результаты поиска

Содержание Formula CG Seating

Отзывы:

Похожие инструкции для Formula CG Seating

Бренды по названию

Популярные бренды