Invacare Formula CG Seating Скачать руководство пользователя | Manualshive

Страница: 104 / 124

background image

7 SETUP/MAINTENANCE

Invacare® Formula™ CG Seating

104

Part No 1143155

4.

Slide the BLACK battery terminal cover back on the BLACK battery cable to expose NEGATIVE battery terminal.

5.

Remove the locknut that secures the bracket of the POSITIVE battery cable to the POSITIVE (+) battery post of the battery.

6.

Remove the locknut that secures the NEGATIVE battery cable to the NEGATIVE(-) battery post of the battery.

7.

Repeat STEPS 2-6 until the existing battery wiring harnesses have been removed.

8.

Position battery connector bracket or wiring harness onto the 22NF battery as shown.

9.

Secure the NEGATIVE battery cable to the NEGATIVE (-) battery post with existing mounting screw and locknut.

10. Secure the bracket of the POSITIVE battery cable to the POSITIVE (+) battery post with existing mounting screw and locknut.
11. Position each battery terminal cover over top of each battery terminal.
12. Secure battery terminal covers in place with one tie-wrap.
13. Repeat STEPS 9-13 to install the remaining wiring harness onto the remaining 22NF battery.
14. Install batteries into wheelchair. Refer to Installing/Removing the Batteries - TDX SP and TDX SR with Elevating Seat on page 93.



WARNING

NEVER allow any of your tools and/or battery cable(s) to contact BOTH battery post(s) at the same time. An electrical

short may occur and serious personal injury or damage may occur.

«
...
102
103
104
105
106
...
»

Содержание Formula CG Seating





























































































































Отзывы:

Нет отзывов

Похожие инструкции для Formula CG Seating

Бренд: GO-ANYWHERE Страницы: 21

MEDLINE MDS89745KDMB

Бренд: Microban Страницы: 8

Бренд: Sizewise Страницы: 34

Бренд: Jay Страницы: 38

ROHO nexus SPIRIT Cushion

Бренд: Permobil Страницы: 10

Bariatric Wheelchair Mover

Бренд: ELECTRODRIVE Страницы: 28

The Eclipse Tilt

Бренд: XXL-Rehab Страницы: 24

Бренд: Preston Ability Страницы: 23

Бренд: baldertech Страницы: 48

Бренд: Paravan Страницы: 127

Yomper 2.5 Plus

Бренд: Acekare Страницы: 46

Бренд: Quickie Страницы: 72

Бренд: Decon wheel Страницы: 6

Бренд: Vitea Care Страницы: 64

Бренд: Travel Buggy Страницы: 13

Бренд: Mobiak Страницы: 19

Бренд: Mobiak Страницы: 20

Бренд: Mobiak Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды