Invacare Formula CG Seating Скачать руководство пользователя

Страница: 94 / 124

7 SETUP/MAINTENANCE

Invacare® Formula™ CG Seating

Part No 1143155

Installing the Batteries

If replacing the batteries, install the front and rear battery wiring harness. Refer to Installing/Removing the Batteries - TDX SP and TDX SR with

Elevating Seat on page 93.

Using the battery handle and strap, position the front battery into the battery box.

Using the battery handle, position the rear battery into the battery box.

position actuator lead and drive limit switch lead under the rear battery handle.

Connect the following:
•

The battery wiring harness to the battery controller connector.

•

The drive limit switch to the magnetic switch controller connector.

•

The elevator actuator to the actuator controller connector.

Install the front top and rear shrouds. Refer to Removing/Installing the Wheelchair Shrouds TDX SP/SR on page 100.

Connect the joystick. Refer to Disconnecting/Connecting the Joysticks on page 86.

Verify the joystick On/Off switch is in the On position and lower the seat.



If replacing the batteries, install the battery wiring harness.

Содержание Formula CG Seating





























































































































Результаты поиска

Содержание Formula CG Seating

Отзывы:

Похожие инструкции для Formula CG Seating

Бренды по названию

Популярные бренды

Invacare Formula CG Seating, Руководство пользователя

Результаты поиска

Содержание Formula CG Seating

Отзывы:

Похожие инструкции для Formula CG Seating

Бренды по названию

Популярные бренды