Invacare Formula CG Seating Скачать руководство пользователя

Страница: 111 / 124

7 SETUP/MAINTENANCE

Part No 1143155

111

Invacare® Formula™ CG Seating

Using the Proper Batteries

Place battery on ground/flat surface.

Visually draw a horizontal and vertical center line through the middle of battery.

Position the battery so that the terminals are above the horizontal center line.

Visually inspect the battery to ensure the correct position of the POSITIVE and NEGATIVE terminals.

FIGURE

Using the Proper Batteries



For this procedure, refer to FIGURE

20.



WARNING

Batteries with terminal configuration as shown below MUST be used. Batteries that have the reverse terminal configuration

MUST NOT be used - otherwise injury and damage may occur.

DO NOT Use

POSITIVE (+)

Battery Terminal

U1 Battery

POSITIVE (+)

Battery Terminal

NEGATIVE (-)

Battery Terminal

Use This Configuration

NEGATIVE (-)

Battery Terminal

Содержание Formula CG Seating





























































































































Результаты поиска

Содержание Formula CG Seating

Отзывы:

Похожие инструкции для Formula CG Seating

Бренды по названию

Популярные бренды

Invacare Formula CG Seating, Руководство пользователя

Результаты поиска

Содержание Formula CG Seating

Отзывы:

Похожие инструкции для Formula CG Seating

Бренды по названию

Популярные бренды