Invacare Formula CG Seating Скачать руководство пользователя

Страница: 34 / 124

5 USAGE

Invacare® Formula™ CG Seating

Part No 1143155

Release four way toggle to neutral position.

FIGURE

Using the Four Way Toggle

Using the CMPJ+ Joystick

Make sure the wheelchair is on a level surface.

Select a drive that has the Actuator Control Switch Mode icon

displayed.

Select the Actuator Control Switch Mode icon (Detail “A”).

Four of the following icons will display when Actuator Control Switch Mode is selected:



For this procedure, refer to FIGURE

3 on page 36.



The location of the icons indicates the joystick direction or quadrant (Detail “B”).

LED

Left

Forward

Rear

Four Way Toggle

Right

Содержание Formula CG Seating





























































































































Результаты поиска

Содержание Formula CG Seating

Отзывы:

Похожие инструкции для Formula CG Seating

Бренды по названию

Популярные бренды

Invacare Formula CG Seating, Руководство пользователя

Результаты поиска

Содержание Formula CG Seating

Отзывы:

Похожие инструкции для Formula CG Seating

Бренды по названию

Популярные бренды