Invacare Formula CG Seating Скачать руководство пользователя | Manualshive

Страница: 106 / 124

background image

7 SETUP/MAINTENANCE

Invacare® Formula™ CG Seating

106

Part No 1143155

Battery Wiring Harness - TDX SP with Vent Tray Option

1.

Remove the existing batteries. Refer to Removing the Batteries on page 98.

2.

Slide the RED battery terminal cover back on the RED battery cable to expose the POSITIVE battery terminal.

3.

Slide the BLACK battery terminal cover back on the BLACK battery cable to expose NEGATIVE battery terminal.

4.

Remove the locknut that secures the bracket of the POSITIVE battery cable to the POSITIVE (+) battery post of the battery.

5.

Remove the locknut that secures the NEGATIVE battery cable to the NEGATIVE(-) battery post of the battery.

6.

Repeat STEPS 2-5 until the existing vent tray, and the right, and left wheelchair battery wiring harnesses have been removed.

7.

Perform STEPS 2-3 of Installing the Batteries on page 99 to position the three 22NF batteries onto the battery tray.

8.

Position battery connector bracket or wiring harness onto the new 22NF battery as shown.

9.

Secure the NEGATIVE battery cable to the NEGATIVE (-) battery post with existing mounting screw and locknut.

10. Secure the bracket of the POSITIVE battery cable to the POSITIVE (+) battery post with existing mounting screw and locknut.
11. Position each battery terminal cover over top of each battery terminal.
12. Secure battery terminal covers in place with one tie-wrap.
13. Repeat STEPS 9-13 until the new front, right, and left batteries wiring harnesses have been installed.
14. TDX SP with Vent Tray Option - Perform STEPS 2-3 of Installing the Batteries on page 99 to position the three 22NF batteries onto the battery

tray.



For this procedure, refer to FIGURE

18 on page 107.

If replacing the batteries or wiring harness, discard the existing item being replaced and perform STEPS 7-14 using the new

batteries or wiring harness.



WARNING

NEVER allow any of your tools and/or battery cable(s) to contact BOTH battery post(s) at the same time. An electrical

short may occur and serious personal injury or damage may occur.

«
...
104
105
106
107
108
...
»

Содержание Formula CG Seating





























































































































Отзывы:

Нет отзывов

Похожие инструкции для Formula CG Seating

Бренд: Pride Mobility Страницы: 44

Бренд: Shoprider Страницы: 24

Бренд: CareCo Страницы: 2

Бренд: CareCo Страницы: 16

Бренд: Quantum Rehab Страницы: 59

Бренд: Quantum Страницы: 24

Бренд: Quantum Страницы: 28

Бренд: Z-Tec Страницы: 9

Бренд: Z-Tec Страницы: 4

Бренд: NRS Healthcare Страницы: 12

Бренд: R82 Страницы: 9

SM-100.5 Series

Бренд: SOMA Страницы: 32

Shower Commode Tilt

Бренд: XXL-Rehab Страницы: 16

Бренд: AAT Страницы: 64

ROHO AGILITY Max Contour Back

Бренд: Permobil Страницы: 104

Бренд: Freedom Страницы: 36

Alante II GP202

Бренд: Golden Страницы: 40

Бренд: WheelAir Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды