Invacare Formula CG Seating Скачать руководство пользователя | Manualshive

Страница: 110 / 124

background image

7 SETUP/MAINTENANCE

Invacare® Formula™ CG Seating

110

Part No 1143155

7.21 Disconnecting/Connecting the Vent Battery Wiring Harness - FDX with Vent Tray Option



WARNING

The use of rubber gloves is recommended when working with batteries.
Invacare strongly recommends that battery installation and battery replacement ALWAYS be done by a qualified technician.
After ANY adjustments, repair or service and before use, make sure all attaching hardware is tightened securely -

otherwise injury or damage may result.
The 22NF battery weighs 24 pounds. Use proper lifting techniques (lift with your legs) to avoid injury.
ALWAYS use a battery lifting strap when lifting a battery. It is the most convenient method and assures that the battery

acid will not spill. It also helps to prolong the life of the battery.
DO NOT tip the batteries. Keep the batteries in an upright position.
NEVER allow any of your tools and/or battery cable(s) to contact BOTH battery post(s) at the same time. An electrical

short may occur and serious personal injury or damage may occur.
When tightening the locknuts, ALWAYS use a box wrench. Pliers will “round off” the nuts. NEVER wiggle the battery

terminal(s)/post(s) when tightening. The battery may become damaged.
The POSITIVE (+) RED battery cable MUST connect to the POSITIVE (+) battery terminal(s)/post(s), otherwise serious

damage will occur to the electrical system.
Install protective caps on POSITIVE (+) and NEGATIVE (-) battery terminals.
DO NOT remove fuse or mounting hardware from POSITIVE (+) RED battery cable.
Unless otherwise indicated, make sure power to the wheelchair is OFF before performing these procedures.
After ANY adjustments, repair or service and before use, make sure all attaching hardware is tightened securely -
otherwise injury or damage may occur.

«
...
108
109
110
111
112
...
»

Содержание Formula CG Seating





























































































































Отзывы:

Нет отзывов

Похожие инструкции для Formula CG Seating

speedstar xtreme

Бренд: Neatech Страницы: 28

Expedition Plus

Бренд: Drive Страницы: 12

Бренд: Roma Medical Страницы: 24

Бренд: Quantum Страницы: 2

Бренд: Quantum Страницы: 2

Бренд: Quantum Страницы: 39

Бренд: Jay Страницы: 7

Shower Chair Series

Бренд: NRS Healthcare Страницы: 2

Бренд: Vermeiren Страницы: 36

Бренд: Permobil Страницы: 52

Бренд: AAT Страницы: 32

Бренд: Abilize Страницы: 28

Бренд: Karma Страницы: 48

Quickie Revolution

Бренд: Sunrise Medical Страницы: 23

Бренд: Sunrise Medical Страницы: 3

Mobility Issue Series

Бренд: Mcombo Страницы: 2

Бренд: WHILL Страницы: 40

Бренд: Vermeiren Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды