Invacare Formula CG Seating Скачать руководство пользователя

Страница: 69 / 124

6 ADJUSTMENT

Part No 1143155

Invacare® Formula™ CG Seating

6.4

Adjusting the Angle of the Manual Center Mount Footrest

Engage the release lever with one hand (not shown) and move the

center mount footrest to the desired angle with the other hand.

Disengage the release lever (not shown) to lock the center mount

footrest in the new position.

FIGURE

Adjusting the Angle of the Manual Center Mount

Footrest



WARNING

While the wheelchair is moving, minimum ground clearance for the front rigging is three inches. If the wheelchair is not moving,

the front rigging MUST maintain a minimum of one inch ground clearance - otherwise personal injury and damage may result.
PINCH POINT EXISTS BETWEEN CENTER MOUNT FOOTREST AND CASTERS - There is limited clearance between

center mount footrest and casters. The user’s feet MUST remain on the center mount footrest while operating the wheelchair. If

the user’s feet are allowed to rest off the side of the center mount footrest they may come in contact with the caster possibly
resulting in injury.



Release lever located towards the front or center

of seat frame.

Footplate

Center Mount

Footrest

Содержание Formula CG Seating





























































































































Результаты поиска

Содержание Formula CG Seating

Отзывы:

Похожие инструкции для Formula CG Seating

Бренды по названию

Популярные бренды

Invacare Formula CG Seating, Руководство пользователя

Результаты поиска

Содержание Formula CG Seating

Отзывы:

Похожие инструкции для Formula CG Seating

Бренды по названию

Популярные бренды