Invacare Formula CG Seating Скачать руководство пользователя

Страница: 114 / 124

7 SETUP/MAINTENANCE

Invacare® Formula™ CG Seating

114

Part No 1143155

•

3G Storm Series

Wheelchairs -

Remove the battery cover from the ventilator battery tray.

ii.

Position the battery onto the ventilator battery tray.

iii. Connect the ventilator battery wiring harness to the battery.
iv. Place the battery cover over the battery.
v.

Secure the ventilator battery strap around the battery cover and ventilator battery tray and clip together.

vi. Connect the ventilator battery harness connector to the ventilator battery harness extension (Detail “A”).

•

TDX SP Wheelchairs Only - Ensure all three 22NF batteries are installed and that the front 22NF battery wiring harness is connected to

the ventilator battery harness connector. Refer to Installing/Removing the Batteries (TDX SP with Vent Tray Option) on page 98.

Wheelchairs with Recline Systems Only - Perform the following steps:
A. Test the recline function of the seating system to ensure that no part of the back assembly interferes with the ventilator tray.
B.

If necessary, contact a qualified technician to adjust the recline down limit to avoid interference with the ventilator tray.

FIGURE

Preparing the Ventilator Tray for Use

Strap

Rear Portion

of Buckle

DETAIL “A” - 3G STORM SERIES

WHEELCHAIR VENTILATOR

BATTERY TRAY

Battery Cover

Ventilator

Battery Tray

Ventilator Tray

Ventilator Battery

Strap

Ventilator Tray

Strap

Содержание Formula CG Seating





























































































































Результаты поиска

Содержание Formula CG Seating

Отзывы:

Похожие инструкции для Formula CG Seating

Бренды по названию

Популярные бренды

Invacare Formula CG Seating, Руководство пользователя

Результаты поиска

Содержание Formula CG Seating

Отзывы:

Похожие инструкции для Formula CG Seating

Бренды по названию

Популярные бренды