Invacare Formula CG Seating Скачать руководство пользователя

Страница: 80 / 124

7 SETUP/MAINTENANCE

Invacare® Formula™ CG Seating

Part No 1143155

7.5

Adjusting/Replacing Telescoping Front Rigging Support

Adjusting

Remove the two cap screws, spacers and threaded blocks securing the telescoping front tube to the side rail.

Slide existing telescoping front rigging support to one of six depth positions.

Use the existing two cap screws, spacers and threaded blocks to secure the telescoping front tube to the side rail:

Repeat STEPS 1 to 3 on the opposite side, if desired.

Replacing

Remove the two cap screws, spacers and threaded blocks securing the telescoping front tube to the side rail.

Remove existing telescoping front rigging.

Perform one of the following:
•

Reclining Seating Systems Only - Refer to Detail “A” in FIGURE

2 to determine the mounting position for the new telescoping front tubes.

•

Non-reclining Seating Systems - The telescoping front tubes can be positioned using one of six mounting positions. Proceed to STEP 4.

Use the existing two cap screws, spacers and threaded blocks to secure the telescoping front tube to the side rail:

Repeat STEPS 1 to 4 on the opposite side, if desired.



WARNING

If the telescoping tubes need to be extended greater than two inches, then the seat must be repositioned rearward to

ensure stability - otherwise personal injury and/or damage to the wheelchair and surrounding property may result.



For this procedure refer to FIGURE

2 on page 81.

Содержание Formula CG Seating





























































































































Результаты поиска

Содержание Formula CG Seating

Отзывы:

Похожие инструкции для Formula CG Seating

Бренды по названию

Популярные бренды

Invacare Formula CG Seating, Руководство пользователя

Результаты поиска

Содержание Formula CG Seating

Отзывы:

Похожие инструкции для Formula CG Seating

Бренды по названию

Популярные бренды