Invacare Formula CG Seating Скачать руководство пользователя

Страница: 26 / 124

4 TECHNICAL DATA

Invacare® Formula™ CG Seating

Part No 1143155

4 Technical Data

4.1

Typical Product Parameters

Models

Seat



All dimensions are ± .50 inches unless otherwise indicated.

Formula CG

FORMULA CG

Seat Width Range

Tilt:
Recline, Tilt/Recline:
Elevate:
Tilt/Elevate:
Tilt/Recline/Elevate:

12 to 24 inches
16 to 24 inches
16 to 22 inches

16 to 24 inches (TDX SP/SR) Only, 16 to 22 inches (All other wheelchairs)
16 to 24 inches (TDX SP/SR) Only, 16 to 22 inches (All other wheelchairs)

Seat Depth Range (1 inch increments)

Tilt:
Recline, Tilt/Recline and Elevate:

12 to 22 inches
16 to 22 inches

Seat-to-Floor Height (0° Seat Angle)

Elevate Only:
Tilt, Recline, Tilt/Recline:
Tilt/Elevate, Tilt/Recline/Elevate:

16.8 ± .5 inch

17.5, 18.5 or 19.5 ± .5 inch

18.5 ± .5 inch

Overall Width

25 to 27 inches

Overall Height:

53 inches

Содержание Formula CG Seating





























































































































Результаты поиска

Содержание Formula CG Seating

Отзывы:

Похожие инструкции для Formula CG Seating

Бренды по названию

Популярные бренды

Invacare Formula CG Seating, Руководство пользователя

Результаты поиска

Содержание Formula CG Seating

Отзывы:

Похожие инструкции для Formula CG Seating

Бренды по названию

Популярные бренды