Invacare Formula CG Seating Скачать руководство пользователя

Страница: 56 / 124

5 USAGE

Invacare® Formula™ CG Seating

Part No 1143155

5.12 Removing/Installing the Manual Center Mount Footrest

Removing

Remove the rigging pivot pin that secures the footrest to the

mounting bracket of the seat frame.

Hold the footrest with one hand and engage the release lever with

the other while simultaneously pulling the center mount footrest

out of the mounting bracket of the seat frame.

Installing

Engage the release lever with one hand, hold the center mount

footrest with the other, and insert the center mount footrest into

the mounting bracket of the seat frame.

Reinstall the rigging pivot pin to secure the center mount footrest

to the mounting bracket of the seat frame.

FIGURE

Removing/Installing the Manual Center Mount Footrest

Rigging Pivot

Center Mount Footrest

Seat Frame Mounting Bracket



Release lever located towards the front

or center of seat frame.

Содержание Formula CG Seating





























































































































Результаты поиска

Содержание Formula CG Seating

Отзывы:

Похожие инструкции для Formula CG Seating

Бренды по названию

Популярные бренды

Invacare Formula CG Seating, Руководство пользователя

Результаты поиска

Содержание Formula CG Seating

Отзывы:

Похожие инструкции для Formula CG Seating

Бренды по названию

Популярные бренды