Invacare Formula CG Seating Скачать руководство пользователя

Страница: 32 / 124

5 USAGE

Invacare® Formula™ CG Seating

Part No 1143155

Using the Single Function Switch

Make sure the wheelchair is on a level surface and that the wheelchair is turned on.

Press and hold the powered seating switch to activate the actuator until the seating system is in the desired position.

Release the powered seating switch after the desired position is achieved.

Using the MK6i SPJ+ w/ACC Joystick

Make sure the wheelchair is on a level surface and that the wheelchair is turned on.

Press the mode button to switch from driving mode to tilt mode.

Move the joystick:

SYSTEM TYPE

JOYSTICK

POWERED SEATING CONTROL

4 POLE MOTOR

SWITCH OPTION

THROUGH THE

JOYSTICK (TTJ)

Single Actuator (Tilt Only, Recline Only or
Elevate Only)

MK6i SPJ+ w/PSS

Single Function Switch (Egg,

Wobble, etc.)

Yes w/SPJ+ w/ACC

CMPJ+/PSR/PSF/DISPLAY w/
Alternate Control

Yes with SANODE

Multiple Actuator (Tilt/Recline or Single
Actuator System with Power Legs)

CMPJ+/PSR/PSF/DISPLAY w/
Alternate Control

4 Way Toggle

Quad Push Button

Replace 4WSB with Multiple

Actuator Interface Box



The powered seating switch will alternate functions (increase tilt angle, decrease tilt angle) after it has been released for a

minimum of three seconds.



For this procedure, refer to FIGURE

6 on page 40.



The LED will light up with a circle around it.

Содержание Formula CG Seating





























































































































Результаты поиска

Содержание Formula CG Seating

Отзывы:

Похожие инструкции для Formula CG Seating

Бренды по названию

Популярные бренды

Invacare Formula CG Seating, Руководство пользователя

Результаты поиска

Содержание Formula CG Seating

Отзывы:

Похожие инструкции для Formula CG Seating

Бренды по названию

Популярные бренды