Invacare Formula CG Seating Скачать руководство пользователя

Страница: 48 / 124

5 USAGE

Invacare® Formula™ CG Seating

Part No 1143155

User Settings

Depress the mode button of the CMPJ+ joystick for 10 seconds and the User Settings screen will appear with three choices. Move the joystick forward

or reverse to scroll through list. Move the joystick to the right to select a user setting.

USER SETTINGS

SET DATE AND TIME

SET DATE AND TIME - Sets the clock on the color CMPJ+ joystick. Adds date and time stamp to error codes.

•

Move the joystick Up or Down to change the highlighted value (hour, minute, AM/PM, month, day, year)

•

Move the joystick Right or Left to select a value or the Set icon.

•

Highlight the Set icon and move the joystick forward to enter new date and time.

BATTERY VOLTAGE

BATTERY VOLTAGE - Displays current battery voltage. This is a diagnostic test a user can perform prior to a
service call.

FAULT CODE

FAULT CODES - Displays time and date stamped fault codes. This information can be helpful to a provider prior to
making a service call

CONNECTED DEVICES

CONNECTED DEVICES - Displays device connections. Refer to Connected Devices Screen on page 49.

User Settings

Set Date and Time

Fault Codes

Connected Devices

Battery Voltage

Содержание Formula CG Seating





























































































































Результаты поиска

Содержание Formula CG Seating

Отзывы:

Похожие инструкции для Formula CG Seating

Бренды по названию

Популярные бренды

Invacare Formula CG Seating, Руководство пользователя

Результаты поиска

Содержание Formula CG Seating

Отзывы:

Похожие инструкции для Formula CG Seating

Бренды по названию

Популярные бренды