Invacare Formula CG Seating Скачать руководство пользователя

Страница: 47 / 124

5 USAGE

Part No 1143155

Invacare® Formula™ CG Seating

FIGURE

LCD Display Screens - Main Screen

Driving Screen

This screen is shown when the operator issues a drive command and the
Drive Icon on the main screen was highlighted.

FIGURE

LCD Display Screens - Driving Screen

Available Modes in this Drive

(Must be Programmed. Top, Highlighted Icon

Indicates Selected Mode)

Clock

Battery Gauge

Display

Status/Info Message Area

Status Indicator

Drive Profile Name



For this procedure, refer to FIGURE

10.



The Drive’s name, warning/info message, status
icon and battery indicator are displayed on this
screen.

Содержание Formula CG Seating





























































































































Результаты поиска

Содержание Formula CG Seating

Отзывы:

Похожие инструкции для Formula CG Seating

Бренды по названию

Популярные бренды

Invacare Formula CG Seating, Руководство пользователя

Результаты поиска

Содержание Formula CG Seating

Отзывы:

Похожие инструкции для Formula CG Seating

Бренды по названию

Популярные бренды