Invacare Formula CG Seating Скачать руководство пользователя

Страница: 85 / 124

7 SETUP/MAINTENANCE

Part No 1143155

Invacare® Formula™ CG Seating

7.9

Repositioning Joystick

Turn the adjustment lock lever to release the joystick mounting tube from the mounting bracket.

Remove the joystick from the wheelchair.

Remove the three hex screws that secure both halves of the mounting bracket to the arm tube.

Reposition mounting bracket on opposite arm tube ensuring the threaded plate of the mounting bracket is on the inside of the arm tube as shown

in FIGURE

Using the three hex mounting screws and washers, secure both halves of the mounting bracket to the arm tube.

Slide the joystick mounting tube through the mounting bracket to the desired position.

Turn the adjustment lock lever to secure the joystick mounting tube into the mounting bracket.

FIGURE

Repositioning Joystick



For this procedure, refer to FIGURE

This procedure must be performed by a qualified technician.

Washers

Hex Mounting

Screws

Mounting Bracket

Adjustment Lock

Lever

Joystick

Mounting

Tube

Mounting

Bracket

(Threaded

Plate)

Arm Tube



Joystick not shown.

Содержание Formula CG Seating





























































































































Результаты поиска

Содержание Formula CG Seating

Отзывы:

Похожие инструкции для Formula CG Seating

Бренды по названию

Популярные бренды

Invacare Formula CG Seating, Руководство пользователя

Результаты поиска

Содержание Formula CG Seating

Отзывы:

Похожие инструкции для Formula CG Seating

Бренды по названию

Популярные бренды