Invacare Formula CG Seating Скачать руководство пользователя

Страница: 79 / 124

7 SETUP/MAINTENANCE

Part No 1143155

Invacare® Formula™ CG Seating

7.4

Replacing Heel Loops

Note the position of hex bolt, coved washers and locknut for

reinstallation.

Remove the hex bolt, coved washers and locknut that secure the

lower footrest to the footrest support.

Remove the lower footrest.

Remove the phillips bolt, spacer and locknut that secure the existing

heel loop to the lower footrest.

Slide the existing heel loop off the lower footrest.

Replace heel loop.

Reverse STEPS 1-6 to reassemble.

FIGURE

Replacing Heel Loops



When securing heel loop to lower footrest,

tighten the phillips screw and locknut until the

spacer is secure.

Footrest Support

Hex Bolt

Phillips Bolt

Spacer

Heel Loop

Locknut

Lower

Footrest

Coved

Washer

Locknut

Содержание Formula CG Seating





























































































































Результаты поиска

Содержание Formula CG Seating

Отзывы:

Похожие инструкции для Formula CG Seating

Бренды по названию

Популярные бренды

Invacare Formula CG Seating, Руководство пользователя

Результаты поиска

Содержание Formula CG Seating

Отзывы:

Похожие инструкции для Formula CG Seating

Бренды по названию

Популярные бренды