Invacare Formula CG Seating Скачать руководство пользователя

Страница: 99 / 124

7 SETUP/MAINTENANCE

Part No 1143155

Invacare® Formula™ CG Seating

Installing the Batteries

If replacing the batteries, install the front and rear battery wiring

harness. Refer to Connecting/Disconnecting the Battery Wiring

Harness - TDX SP and TDX SR with Elevating Seat Only on

page 102.

Position the right and left batteries onto the rear of the battery tray.

•

Position the front battery onto the front of the battery tray.

•

Connect the right battery to the left battery.

Connect battery straps.

Slide the battery tray into the wheelchair.

Connect the wiring harness from the controller connector.

Connect the front battery wiring harness from the ventilator

connector.

Install the rear shroud, front shroud and battery retention bracket.

Refer to Removing/Installing the Wheelchair Shrouds TDX SP/SR

on page 100.

Connect the joystick. Refer to Disconnecting/Connecting the

Joysticks on page 86.

FIGURE

Installing/Removing the Batteries (TDX SP with Vent

Tray Option)



Front of battery tray is designated by the battery

stop. Rear of the battery tray is the opposite end.
Orientation of the battery is critical otherwise

batteries will not connect to the controller or

each other.

Disconnect Front Battery

Harness from the

Ventilator Connector

Here

FRONT OF

WHEELCHAIR

Left Battery

Front

Battery

Straps



Battery tray shown

removed for clarity.

Battery Tray

Disconnect Battery Harness from the

Controller Connector Here

Disconnect the Right Battery from

the Left Battery Here

Right Battery

Содержание Formula CG Seating





























































































































Результаты поиска

Содержание Formula CG Seating

Отзывы:

Похожие инструкции для Formula CG Seating

Бренды по названию

Популярные бренды

Invacare Formula CG Seating, Руководство пользователя

Результаты поиска

Содержание Formula CG Seating

Отзывы:

Похожие инструкции для Formula CG Seating

Бренды по названию

Популярные бренды