Invacare Formula CG Seating Скачать руководство пользователя

Страница: 100 / 124

7 SETUP/MAINTENANCE

Invacare® Formula™ CG Seating

100

Part No 1143155

7.18 Removing/Installing the Wheelchair Shrouds TDX SP/SR

Rear shroud

Remove the three pan head screws that secure the rear shroud to the base frame.

Remove the rear shroud from the base frame.

Front Shroud and Battery Retention Bracket

Remove the two socket head screws securing the front shroud/battery retention bracket to the base frame.

Lift up to unhook the battery retention bracket from the base frame and remove the front shroud/battery retention bracket from the base frame.

Top Shroud

Remove the seat from the base frame.

Remove the four pan head screws securing the top shroud to the base frame.

Lifting up, remove the top shroud from the base frame.



For this procedure, refer to FIGURE

16 on page 101.



Reverse this procedure to install the rear shroud.



Reverse this procedure to install the front shroud and battery retention bracket.
The front shroud and battery retention bracket are removed from and installed onto the wheelchair frame as a single unit.



Reverse this procedure to install the top shroud.

Содержание Formula CG Seating





























































































































Результаты поиска

Содержание Formula CG Seating

Отзывы:

Похожие инструкции для Formula CG Seating

Бренды по названию

Популярные бренды

Invacare Formula CG Seating, Руководство пользователя

Результаты поиска

Содержание Formula CG Seating

Отзывы:

Похожие инструкции для Formula CG Seating

Бренды по названию

Популярные бренды