Invacare Formula CG Seating Скачать руководство пользователя

Страница: 84 / 124

7 SETUP/MAINTENANCE

Invacare® Formula™ CG Seating

Part No 1143155

7.8 Composite/Articulating Footplate Heel

Loop Replacement

Disassembly

Composite

Remove the mounting screw and coved washer that secures the

lower half of the footrest to the swingaway footrest assembly.

Remove the lower footrest assembly.

Remove the mounting screw and locknut that secure the heel loop

to the footrest.

Slide heel strap over cane of footrest assembly.

Articulating

Remove the two mounting screws that secure the heel loop to the

articulating footplate.

Assembly

Replace heel strap/loop.

Reverse steps in Disassembly to assemble.

FIGURE

Composite/Articulating Footplate Heel Loop

Replacement



When securing heel loop to the footrest assembly,

tighten mounting screw until the spacer is secure.

Composite

Articulating

Mounting Screw

Spacer

Composite

Footplate

Locknut

Mounting Screw

Heel Loop

Articulating

Footplate

Cane of Footrest Assembly

Содержание Formula CG Seating





























































































































Результаты поиска

Содержание Formula CG Seating

Отзывы:

Похожие инструкции для Formula CG Seating

Бренды по названию

Популярные бренды

Invacare Formula CG Seating, Руководство пользователя

Результаты поиска

Содержание Formula CG Seating

Отзывы:

Похожие инструкции для Formula CG Seating

Бренды по названию

Популярные бренды