Invacare Formula CG Seating Скачать руководство пользователя

Страница: 43 / 124

5 USAGE

Part No 1143155

Invacare® Formula™ CG Seating

5.6

CMPJ+ Joystick Switches and Indicators

On/Off - Drive Select Toggle Switch

The drive select toggle switch is located on the left side, below the LCD. The drive select position is momentary, meaning that it will return to the

neutral position after a selection is made.
This switch allows the operator to select the type of operation or performance which best suits a particular control need or situation. The DRIVE 1

program uses performance values which are independent of those used for the DRIVE 2 or 3 or 4 program. As an example, an operator may have a

control need for spasticity in the morning and a very different need in the afternoon. DRIVE 1 can be programmed for higher speeds and quicker

response while DRIVE 2 can be programmed for slower speeds and less responsiveness or vise versa. The other two drive programs could be indoor

and outdoor versions of DRIVE 1 and DRIVE 2.

Selecting the Drive Mode

Move the toggle up and release. DRIVE 1 will appear on LCD.

Move the toggle up and release again. DRIVE 2 will appear on LCD.

Move the toggle up and release again. DRIVE 3 will appear on LCD.

Move the toggle up and release again. DRIVE 4 will appear on LCD.

Move the toggle up and release one more time to select DRIVE 1.

FIGURE

CMPJ+ Joystick Switches and Indicators



For this procedure, refer to FIGURE

Joystick

Remote On/Off

Input

Programmable Mono

Port 1/2 or External

Mode Switch

To Controller

On/Off - Drive Select

Toggle Switch

LCD Display

Speed Control

Knob

Charger/Programming

Input (Front of Joystick)

Memory Card Slot

Mode Switch

Содержание Formula CG Seating





























































































































Результаты поиска

Содержание Formula CG Seating

Отзывы:

Похожие инструкции для Formula CG Seating

Бренды по названию

Популярные бренды

Invacare Formula CG Seating, Руководство пользователя

Результаты поиска

Содержание Formula CG Seating

Отзывы:

Похожие инструкции для Formula CG Seating

Бренды по названию

Популярные бренды