Invacare Formula CG Seating Скачать руководство пользователя

Страница: 59 / 124

5 USAGE

Part No 1143155

Invacare® Formula™ CG Seating

5.14 Installing/Removing Flip Back Armrests

Installing

Visually inspect to ensure flip back armrest release lever is in the

unlocked (up-horizontal) position.

Slide the flip back armrest into the arm sockets on the seat frame.

Install the quick-release pin through the rear arm socket and flip

back armrest.

Lock the flip back armrest by pressing the flip back armrest release

lever into the down (vertical) position.

Repeat STEPS 1-4

for the opposite flip back armrest.

Removing

Unlock the flip back armrest by positioning the flip back armrest

release lever into the up (horizontal) position.

Remove the quick-release pin that secures the flip back armrest to

the rear arm socket.

Pull UP on the flip back armrest and remove the armrest from the

arm sockets.

Repeat STEPS 1-3

for the opposite flip back armrest, if necessary.

FIGURE

Installing/Removing Footrests



WARNING

Make sure the flip back armrest release and height adjustment levers are in the locked position before using the wheelchair.



Flip back armrest release lever must be in the unlocked (up-horizontal) position when placing the armrest into the arm

sockets.

Locked

(Down -

Vertical)

Unlocked

(Up -

Horizontal)

Flip Back

Armrest

Release Lever

Flip Back

Armrest

Rear Arm

Socket

Quick-Release Pin

Seat Frame

Front Arm Socket

Содержание Formula CG Seating





























































































































Результаты поиска

Содержание Formula CG Seating

Отзывы:

Похожие инструкции для Formula CG Seating

Бренды по названию

Популярные бренды

Invacare Formula CG Seating, Руководство пользователя

Результаты поиска

Содержание Formula CG Seating

Отзывы:

Похожие инструкции для Formula CG Seating

Бренды по названию

Популярные бренды