Invacare Formula CG Seating Скачать руководство пользователя

Страница: 112 / 124

7 SETUP/MAINTENANCE

Invacare® Formula™ CG Seating

112

Part No 1143155

Disconnecting/Connecting the Vent Battery Wiring Harness - FDX with Vent Tray Option

Remove the existing vent tray battery. Refer to Removing/Installing

the Vent Battery on page 108.

Cut the tie-wrap that secures the battery terminal cap in place.

Slide the RED battery terminal cover back on the RED battery cable

to expose the POSITIVE battery terminal.

Slide the BLACK battery terminal cover back on the BLACK
battery cable to expose NEGATIVE battery terminal.

Remove the locknut and mounting screw that secures the

POSITIVE battery cable to the POSITIVE (+) battery post of the

battery.

Remove the locknut and mounting screw that secures the

NEGATIVE battery cable to the NEGATIVE(-) battery post of the

battery.

Reverse STEPS 3-6 to connect the vent battery wiring harness to

the vent battery.

FIGURE

Disconnecting/Connecting the Vent Battery Wiring

Harness - FDX with Vent Tray Option



For this procedure, refer to FIGURE

21 on

page 112.
If replacing the vent battery or the vent battery

wiring harness, discard the existing item being

replaced and perform STEP 7 using the new vent

battery or vent battery wiring harness.
Reverse this procedure to connect the vent

battery wiring harness.



WARNING

NEVER allow any of your tools and/or battery
cable(s) to contact BOTH battery post(s) at the
same time. An electrical short may occur and
serious personal injury or damage may occur.

POSITIVE (+)

Battery Terminal

NEGATIVE (-)

Battery Cable

NEGATIVE (-)

Battery Terminal

Vent Battery Wiring

Harness

Mounting Screw

POSITIVE (+)

Battery Cable

Mounting

Screw

Locknuts

Vent

Battery



Terminal caps and tie-wraps not shown.
Use new tie-wraps when connecting the vent battery

wiring harness.

Содержание Formula CG Seating





























































































































Результаты поиска

Содержание Formula CG Seating

Отзывы:

Похожие инструкции для Formula CG Seating

Бренды по названию

Популярные бренды

Invacare Formula CG Seating, Руководство пользователя

Результаты поиска

Содержание Formula CG Seating

Отзывы:

Похожие инструкции для Formula CG Seating

Бренды по названию

Популярные бренды