Invacare Formula CG Seating Скачать руководство пользователя

Страница: 33 / 124

5 USAGE

Part No 1143155

Invacare® Formula™ CG Seating

•

Forward - Tilts or reclines the seat back or elevates the seat.

•

Backward - Returns the seat to the upright position or lowers the seat.

Using the Four Way Toggle

Make sure the wheelchair is on a level surface.

Refer to the chart for the operation of the seating system using a four way toggle.



For this procedure refer to FIGURE

2 on page 34



The chart shows the factory programmed settings only. Switch assignments can be reprogrammed.

SEATING SYSTEM

FOUR WAY TOGGLE

FORWARD

REAR

LEFT

RIGHT

Formula CG - Tilt Only

Decrease the Tilt Angle

Increase the Tilt Angle

OFF

Formula CG - Recline
w/Legs

Decrease the Recline

Angle

Increase the Recline Angle

Power Legrest Up

Power Legrest Down

Formula CG - Tilt/Recline

Decrease the

Tilt Angle & Legs Down

Increase the

Tilt Angle & Legs Up

Decrease the Recline

Angle

Increase the Recline Angle

Formula CG - Elevate Only

Elevate Up

Elevate Down

OFF

Formula CG - Tilt/Recline/
Elevate w/Legs

Increase/Decrease the Tilt

Angle

Increase/Decrease the

Recline Angle and Power

legrest Up/Down.

Elevate Up/Down

Power Legrest

Up/Down

Formula CG - Tilt/Recline w/
Legs

Increase/Decrease the Tilt

Angle

Increase/Decrease the

Recline Angle and Power

legrest Up/Down.

Power Legrest Up

Power Legrest Down

Formula CG - Tilt/Elevate

Decrease the

Tilt Angle

Increase the

Tilt Angle

Elevate Up

Elevate Down

Legs Only

Power Legrest Up

Power Legrest Down

OFF

Содержание Formula CG Seating





























































































































Результаты поиска

Содержание Formula CG Seating

Отзывы:

Похожие инструкции для Formula CG Seating

Бренды по названию

Популярные бренды

Invacare Formula CG Seating, Руководство пользователя

Результаты поиска

Содержание Formula CG Seating

Отзывы:

Похожие инструкции для Formula CG Seating

Бренды по названию

Популярные бренды