Invacare Formula CG Seating Скачать руководство пользователя

Страница: 68 / 124

6 ADJUSTMENT

Invacare® Formula™ CG Seating

Part No 1143155

6.3

Adjusting the Height of the Manual Center Mount Footrest

Remove the two mounting screws that secure the button head cleat

to the extension housing.

Adjust the footrest extension tube to the desired height.

Secure the extension tube to the desired height with the button

head cleat and mounting screws. Securely tighten.

Repeat STEPS 1-3 for the other extension tube.

FIGURE

Adjusting the Height of the Manual Center Mount

Footrest



WARNING

While the wheelchair is moving, minimum ground clearance for the front rigging is three inches. If the wheelchair is not moving,

the front rigging MUST maintain a minimum of one inch ground clearance - otherwise personal injury and damage may result.
PINCH POINT EXISTS BETWEEN CENTER MOUNT FOOTREST AND CASTERS - There is limited clearance between

center mount footrest and casters. The user’s feet MUST remain on the center mount footrest while operating the wheelchair. If

the user’s feet are allowed to rest off the side of the center mount footrest they may come in contact with the caster possibly
resulting in injury.

Extension Housing

Extension Tube

Mounting

Screws

Extension Tube

Mounting Holes

Button Head

Cleat

Содержание Formula CG Seating





























































































































Результаты поиска

Содержание Formula CG Seating

Отзывы:

Похожие инструкции для Formula CG Seating

Бренды по названию

Популярные бренды

Invacare Formula CG Seating, Руководство пользователя

Результаты поиска

Содержание Formula CG Seating

Отзывы:

Похожие инструкции для Formula CG Seating

Бренды по названию

Популярные бренды