Invacare Formula CG Seating Скачать руководство пользователя

Страница: 64 / 124

6 ADJUSTMENT

Invacare® Formula™ CG Seating

Part No 1143155

70° and PW93

Remove any accessory from the footrest(s).

Remove the footrest from the wheelchair. Refer to Installing/

Removing Footrests on page 52.

Remove the mounting screw, washers and locknut that secure the

lower footrest assembly to the upper footrest support (FIGURE

2).

Reposition the lower footrest to the desired height.

Reinstall the mounting screw, washers and locknut that secure the

lower footrest to the footrest support and tighten securely.

Repeat STEPS 1-5

for the opposite wheelchair footrest, if

necessary.

Reinstall the footrest(s) onto the wheelchair. Refer to Installing/

Removing Footrests on page 52.

Reinstall any accessory onto the footrest(s).

FIGURE

Footrest Height Adjustment - 70° and PW93



Lay the footrest on a flat surface to simplify this

procedure.

Footrest Support

Coved

Washer

Hex Bolt

Lower

Footrest

Coved

Washer

Locknut

Содержание Formula CG Seating





























































































































Результаты поиска

Содержание Formula CG Seating

Отзывы:

Похожие инструкции для Formula CG Seating

Бренды по названию

Популярные бренды

Invacare Formula CG Seating, Руководство пользователя

Результаты поиска

Содержание Formula CG Seating

Отзывы:

Похожие инструкции для Formula CG Seating

Бренды по названию

Популярные бренды