manualshive.com logo in svg

Huawei OptiX OSN 550, Руководство по настройке, Страница: 159 / 470

Поделиться
Скачать
Huawei OptiX OSN 550 Скачать руководство пользователя страница 159

 

The corresponding relations between the PORTs and the VCTRUNKs are provided in 

Table

4-3

.

Table 4-3

 Corresponding relations between the PORTs and the VCTRUNKs (VCTRUNK-

shared EVPL services)

NE1

NE2

User D1

PORT1

←→

VCTRUNK1

VCTRUNK1

←→

PORT1

User D2

User E1

PORT2

←→

VCTRUNK1

VCTRUNK1

←→

PORT2

User E2

 

EPLAN Services

The EPLAN services can be accessed from a minimum of two nodes. Hence, the services of
different users need not share the bandwidth. That is, in the case of EPLAN services, a bandwidth
is exclusively occupied by the service of a user and the services of different users are isolated.
In addition, the extra QoS scheme and security scheme are not required. The EPLAN services
have more than one node. Hence, the nodes need to learn the MAC addresses and forward data
according to MAC addresses. Therefore, Layer 2 switching is realized.

As shown in 

Figure 4-4

, three branches of user F need to communicate with each other. On

NE1, the IEEE 802.1d bridge is established to achieve EPLAN services. The IEEE 802.1d bridge
can create the MAC address-based forwarding table, which is periodically updated by using the
self-learning function of the system. The accessed data can be forwarded or broadcast within
the domain of the IEEE 802.1d bridge according to the destination MAC addresses.

Figure 4-4

 EPLAN services (IEEE 802.1d bridge)

F1

PORT5

U2000

NE3

NE2

NE1

NE4

VCTRUNK

F3

PORT1

F2

PORT1

PORT5

VCTRUNK1

VCTRUNK2

IEEE 802.1d bridge

 

OptiX OSN 550 Multi-Service CPE Optical Transmission
System
Configuration Guide

4 Configuring Ethernet Services

Issue 02 (2011-06-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

4-5

Содержание OptiX OSN 550























































































































































































































































































































































































































































































Отзывы:

Нет отзывов