manualshive.com logo in svg

Hitachi H8S/2627, Руководство по оборудованию, Страница: 521 / 605

Поделиться
Скачать
Hitachi H8S/2627 Скачать руководство пользователя страница 521

Rev. 1.0, 09/02, page 485 of 568 

 

21.4 

Software Standby Mode 

21.4.1 

Transition to Software Standby Mode 

A transition is made to software standby mode if the SLEEP instruction is executed when the 
SBYCR SSBY bit is set to 1. In this mode, the CPU, on-chip peripheral modules, and oscillator, 
all stop. However, the contents of the CPU’s internal registers, on-chip RAM data, and the states 
of on-chip peripheral modules other than the SCI, A/D converter, and the states of I/O ports, are 
retained. In this mode, the oscillator stops, and therefore power consumption is significantly 
reduced. 

21.4.2 

Clearing Software Standby Mode 

Software standby mode is cleared by an external interrupt (NMI pin, or pins 

IRQ0

 to 

IRQ5

), or by 

means of the 

RES

 pin or 

STBY

 pin. 

•

 

Clearing with an interrupt 

When an NMI or IRQ0 to IRQ5 interrupt request signal is input, clock oscillation starts, and 
after the time set in bits STS0 to STS2 in SBYCR has elapsed, stable clocks are supplied to the 
entire chip, software standby mode is cleared, and interrupt exception handling is started. 

When clearing software standby mode with an IRQ0 to IRQ5 interrupt, set the corresponding 
enable bit to 1 and ensure that no interrupt with a higher priority than interrupts IRQ0 to IRQ5 
is generated. Software standby mode cannot be cleared if the interrupt has been masked on the 
CPU side or has been designated as a DTC activation source. 

•

 

Clearing with the 

RES

 pin 

When the 

RES

 pin is driven low, clock oscillation is started. At the same time as clock 

oscillation starts, clocks are supplied to the entire chip. Note that the 

RES

 pin must be held low 

until clock oscillation settles. When the 

RES

 pin goes high, the CPU begins reset exception 

handling. 

•

 

Clearing with the 

STBY

 pin 

When the 

STBY

 pin is driven low, a transition is made to hardware standby mode. 

 

Содержание H8S/2627






























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов