Hitachi H8S/2627 Скачать руководство пользователя страница 327 | Manualshive

Страница: 327 / 605

background image

Rev. 1.0, 09/02, page 291 of 568

Section 14 Serial Communication Interface (SCI)

This LSI has two independent serial communication interface (SCI) channels. The SCI can handle
both asynchronous and clocked synchronous serial communication. Serial data communication
can be carried out using standard asynchronous communication chips such as a Universal
Asynchronous Receiver/Transmitter (UART) or an Asynchronous Communication Interface
Adapter (ACIA). A function is also provided for serial communication between processors
(multiprocessor communication function). The SCI also supports an IC card (Smart Card)
interface conforming to ISO/IEC 7816-3 (Identification Card) as a serial communication interface
extension function.

Figure 14.1 shows a block diagram of the SCI.

14.1 Features

•

Choice of asynchronous or clocked synchronous serial communication mode

•

Full-duplex communication capability

The transmitter and receiver are mutually independent, enabling transmission and reception to
be executed simultaneously.

Double-buffering is used in both the transmitter and the receiver, enabling continuous
transmission and continuous reception of serial data.

•

On-chip baud rate generator allows any bit rate to be selected

External clock can be selected as a transfer clock source (except for in Smart Card interface
mode).

•

Choice of LSB-first or MSB-first transfer (except in the case of asynchronous mode 7-bit data)

•

Four interrupt sources

Transmit-end, transmit-data-empty, receive-data-full, and receive error



that can issue

requests.

The transmit-data-empty interrupt and receive data full interrupts can be used to activate the
data transfer controller (DTC).

•

Module stop mode can be set

Asynchronous mode

•

Data length: 7 or 8 bits

•

Stop bit length: 1 or 2 bits

•

Parity: Even, odd, or none

•

Receive error detection: Parity, overrun, and framing errors

•

Break detection: Break can be detected by reading the RxD pin level directly in the case of a
framing error

SCI0027A_0100020020900

«
...
325
326
327
328
329
...
»

Содержание H8S/2627






























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для H8S/2627

All in One Printer

Бренд: Baracoda Страницы: 42

Бренд: Harmonic Страницы: 56

Бренд: Fracarro Страницы: 12

MultiConnect SE MTS2EA

Бренд: Multitech Страницы: 2

Бренд: Zoom Страницы: 48

PoleVault System A/V Source Inputs

Бренд: Extron electronics Страницы: 4

Бренд: Tektronix Страницы: 178

RADEON 9800 PRO

Бренд: ATI Technologies Страницы: 20

Бренд: Xantech Страницы: 16

Бренд: Xilinx Страницы: 27

High-Precision AD/DA Board

Бренд: Waveshare Страницы: 8

Бренд: ETAS Страницы: 29

Бренд: LST Страницы: 1

Бренд: JETWAY Страницы: 63

airPoint Nexus sB3210

Бренд: SmartBridges Страницы: 55

Бренд: Aerotech Страницы: 62

Бренд: Radio Shack Страницы: 154

Бренд: ZyXEL Communications Страницы: 114

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды