Harmonic Ellipse 3000 Скачать руководство пользователя страница 97

Страница: 97 / 403

Chapter 4 Transport Stream Configuration

Ellipse 3000 Release 3.0, Rev. B

M-SPTS Sub-Menu/Tab

4.3.2

M-SPTS Configuration Management

The M-SPTS stream managing enables you to monitor and configure the following parameters of
a selected M-SPTS transport stream:

■

MSPTS

sub-menu/box

❑

Transport Name – The name of the M-SPTS transport (free text).

❑

Add PID

and

List/Drop PID

– Provides access to setting the PID parameters for the M-SPTS

stream (for details, refer to

4.3.2.3 M-SPTS PID Management (Add / Drop PID)

on page 102).

■

General

sub-menu/box

❑

Protocol

– The IP-output interface protocol used by the stream (UDP or RTP)

(FEC Enabled only).

❑

Number of Packets

– The number of transport-stream packets per IP frame.

Range 1 to 7. Default:

❑

Transport Name

– (FEC Disabled only)

❑

Activation

– Status of the stream (Enabled/Disabled) (FEC Disabled only)

❑

Transport Rate

– The rate of the stream (Range: 350,000 to 70,000,000) (FEC Disabled only).

❑

Transport ID

– The identification number of the stream (Range: 1 to 65535)

(FEC Disabled only).

❑

Network ID

– The identification number of the network (Range: 0x1 to 0x65535, hex)

(FEC Disabled only).

❑

Network Name

– The name of the network (free text) (FEC Disabled only).

❑

FEC Activation

– (FEC Enabled only)

❑

FEC Dimension

– (FEC Enabled only)

❑

FEC Column Number

– (FEC Enabled only)

❑

FEC Row Number

– (FEC Enabled only)

❑

Cascading Included

– (FEC Disabled only)

❑

Physical Port Activation

– (FEC Enabled only)

■

IP1/IP2

sub-menu/box – Provides access to the stream IP1 / IP2 detailed parameters (for

details, refer to

4.3.2.1 IP1/IP2 Configuration

on page 100).

■

Advanced

sub-menu/box – Provides access to advanced functions of the stream (for details,

refer to

4.3.2.2 Advanced Stream Functions

on page 101) (FEC Disabled only).

■

PID sub-menu/box – (FEC Disabled only)

NOTE:

Some parameters only display when

FEC Activation

and

Cascading Included

are disabled, conversely

some parameters only display when

EC Activation

Cascading Included

are enabled.

Содержание Ellipse 3000















































































































































































































































































































































































































Результаты поиска

Содержание Ellipse 3000

Отзывы:

Похожие инструкции для Ellipse 3000

Бренды по названию

Популярные бренды

Harmonic Ellipse 3000, Руководство пользователя

Результаты поиска

Содержание Ellipse 3000

Отзывы:

Похожие инструкции для Ellipse 3000

Бренды по названию

Популярные бренды