Harmonic Ellipse 3000 Скачать руководство пользователя страница 185 | Manualshive

Страница: 185 / 403

background image

Chapter 6 Audio Configuration

© 2013 Harmonic Inc. Harmonic All rights reserved.

185

Ellipse 3000 Release 3.0, Rev. B

Coding Scheme Configuration

6.5.3.3

RF Over Modulation Protection (DD 2.0 Pre-Processing)

The RF Over Modulation Protection parameter enables the RF over-modulation protection to
prevent the Dolby Digital 2.0 decoded audio signal from being over-modulated when it is RF
modulated.

The available options are:

■

Off

– RF over-modulation protector is disabled.

■

On

– RF over-modulation protector is enabled.

The Dolby Pre-Processing RF Over modulation protection default is

Off

.

Front Panel

To set the RF-Over Modulation Protection parameter on the front panel:

❖

Navigate

Root > Configuration > Audio > [Audio Channel] > Pre-Processing >

RF Overmodulation Protection

.

Web Manager

To set the Dolby Pre-Processing RF Over modulation protection parameter in the Web Manager:

❖

Select

Audio > Aud#

and access the Pre-Processing parameters box.

6.5.3.4

LFE LPF Enable

Use the LFE LPF Enable parameter to set the Dolby Digital 5.1 LFE low pass filter.

The available options are:

■

On

■

Off

The LFE LPF default is

Off

.

Front Panel

To set the LFE LPF on the front panel:

❖

Navigate

Root > Configuration > Audio > [Audio Channel] > Pre-Processing > Low-Pass

Filter

.

Web Manager

To set the LFE LPF Enable parameter in the Web Manager:

❖

Select

Audio > Aud#

and access the Pre-Processing parameters box.

RF Overmodulation Protection

1 ‚ Off

2 ƒ On

«
...
183
184
185
186
187
...
»

Содержание Ellipse 3000




















































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Ellipse 3000

Бренд: Xblitz Страницы: 18

Professional Series

Бренд: IFCS Страницы: 2

Бренд: Robotics Technologies Страницы: 11

Бренд: Guardian Страницы: 47

Бренд: CP Plus Страницы: 105

Бренд: CP Plus Страницы: 253

Бренд: Covert Страницы: 9

Бренд: Velleman Страницы: 39

Бренд: EOS Australia PTY LTD Страницы: 41

Бренд: Bang & Olufsen Страницы: 56

Бренд: Advanced Technology Video Страницы: 22

UNIARCH XVR-108G

Бренд: UNIVIEW Страницы: 3

Бренд: Plustek Страницы: 33

DS-8100-S Series

Бренд: HIKVISION Страницы: 4

DS-8000AH(F)(L)I-S Series

Бренд: HIKVISION Страницы: 116

Бренд: HIKVISION Страницы: 113

Бренд: 4NSYS Страницы: 87

DVMRe -16CS Simplex

Бренд: GE Security Страницы: 92

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды