manualshive.com logo in svg

Harmonic Ellipse 3000, Руководство пользователя, Страница: 183 / 403

Поделиться
Скачать
Harmonic Ellipse 3000 Скачать руководство пользователя страница 183

Chapter 6 Audio Configuration

 © 2013 Harmonic Inc. Harmonic All rights reserved.

183

Ellipse 3000 Release 3.0, Rev. B

Coding Scheme Configuration

6.5.3.1

Low Pass Filter (Dolby Digital 2.0 and Dolby Digital 5.1 Pre-Processing)

The Low-Pass Filter parameter sets the Dolby Digital 2.0 and Dolby Digital 5.1 Pre-Processing low 
pass filter mode of operation.

The available options are:

■

Off

 – Low-pass filter is disabled.

■

On

 – Low-pass filter is enabled.

The Dolby Pre-Processing Low-Pass Filter default is 

On

.

Front Panel

To set the Dolby Pre-Processing Low-Pass Filter parameter on the front panel:

❖

Navigate 

Root > Configuration > Audio > [Audio Channel] > Pre-Processing > Low-Pass 

Filter

.

Web Manager

To set the Dolby Pre-Processing Low-Pass Filter parameter in the Web Manager:

❖

Select 

Audio > Aud#

 and access the Pre-Processing parameters box.

 Low Pass Filter 

‚ Off

ƒ On

Содержание Ellipse 3000




















































































































































































































































































































































































































Отзывы:

Нет отзывов