Harmonic Ellipse 3000 Скачать руководство пользователя страница 159

Страница: 159 / 403

Chapter 6 Audio Configuration

159

Ellipse 3000 Release 3.0, Rev. B

Coding Scheme Configuration

6.5.1.1

Encoding Mode (MPEG-1 Layer 2)

The Encoding Mode parameter sets the operation mode of the MPEG-1 Layer 2 audio channel.

The available options are:

■

L,R Dual PIDs

– Encoding mode allows two different audio PIDs (elementary-streams) to be

transferred through the left and the right.

■

Mono (L only)

– Encoding mode is set to single, mono channel. Mono channel is always left.

■

Dual Mono

– Encoding mode allows two independent channels, carrying the same audio PIDs.

■

Stereo

– Encoding mode is set to stereo for encoding a stereophonic audio signal.

■

Joint Stereo

– Encoding mode is set to joint stereo. Joint stereo is used for more efficient

combined encoding of the left and right channels of a stereophonic audio signal.

The MPEG-1 Layer 2 Encoding mode default value is

Stereo

Front Panel

To set the Encoding Mode parameter on the front panel:

❖

Navigate

Root > Configuration > Audio > [Audio Channel] > MPEG-1 Layer 2 Parameters >
Encoding Mode

Web Manager

To set the MPEG-1 Layer 2 Encoding Mode parameter in the Web Manager:

❖

Select

Audio > Aud#

and access the MPEG-1 layer 2 Parameters menu.

Encoding Mode

1 ‚ L,R Dual PIDs

2 ‚ Mono (L only)

3 ƒ Dual Mono

4 ‚ Stereo

5 ‚ Joint Stereo

Содержание Ellipse 3000















































































































































































































































































































































































































Результаты поиска

Содержание Ellipse 3000

Отзывы:

Harmonic Ellipse 3000, Руководство пользователя, Страница: 159 / 403

Результаты поиска

Содержание Ellipse 3000

Отзывы: