Harmonic Ellipse 3000 Скачать руководство пользователя страница 311

Страница: 311 / 403

Chapter 11 DSNG Configuration

311

Ellipse 3000 Release 3.0, Rev. B

IF Modulator Parameters

Front Panel

To access the IF Modulation menu on the front panel:

❖

Navigate

Root > IF Modulation

IF Modulation

IF Power

-8

Reduced IF Power

Modulation on/off

Off

Carrier

Symbol Rate

10000000

Spectrum Inversion

Direct

Modulation Scheme

DVB-S

FEC and Modulation

QPSK 2/3

IF Frequency

070000000

L-Band Monitor Frequency

0950000

Output Impedance

50 ohm

Frame Length

32000 bits

Operating Mode

C and M Restore...

Roll-Off Factor

0.35

Pilot Mode

Off

Содержание Ellipse 3000















































































































































































































































































































































































































Результаты поиска

Содержание Ellipse 3000

Отзывы:

Harmonic Ellipse 3000, Руководство пользователя, Страница: 311 / 403

Результаты поиска

Содержание Ellipse 3000

Отзывы: